Blue and White Suburban Home.

Properly Managing the Exterior Moisture Envelope

A dry home is a happy home, and it starts by properly managing the exterior moisture envelope. The exterior walls on every home serve as the structural base for the installation of siding and decorative trim as well as the windows and doors and is the largest expanse (outside of the roof) of the moisture envelope. Everything that is attached to the exterior walls must be properly installed and sealed to ensure that the inside of the home stays dry.

Use the right product. 

There are many options available to the builder when it comes to siding and exterior trim in addition to all-natural wood. Composite building products are on that list, and they include materials like concrete, reinforced plastics, cement, steel, wood fibers, and glue. While these manufactured products boast ease of installation when used within their systems, there are very detailed instructions that must be followed to ensure that moisture is not allowed to get behind them and reach the exterior walls.

Use the right technique.

Whether you are using all-natural wood or a manufactured product for siding and exterior trim, the product must be installed by following the manufacturer’s recommendations to ensure its effectiveness on the home. The trades doing the installation must be aware of the most current recommended standards for attaching trim and siding products as well as knowledgeable concerning the types of fasteners that work best for a given product in a particular environment.

Treat siding joints properly.

The proper installation of wood or composite siding involves more than making sure the nails are hitting a stud. Every joint that is formed when two pieces of siding meet (called a butt-joint) must be properly flashed, or there will eventually be a leak in that location. The method that is recommended to eliminate this situation is called back-flashing and involves using an approved flashing material (felt paper, house wrap, etc.) that goes behind the butt-joint and overlaps the piece of siding below to shed the water away from the wall and onto the siding. It is not recommended to caulk butt-joints. There may be hundreds of them on an average home, and over time, these joints will have to have maintenance and require re-painting as the caulk eventually fails.

Caulk siding end joints with correct sealant.

Where siding meets a piece of trim, there needs to be caulk applied to ensure the maximum protection from moisture. The type of caul used will depend upon the siding. For most siding, you will want to look for caulks that remain permanently flexible.  Silicone, acrylic latex, solvent-based, elastomeric, and butyl rubber are some of the most common types. Fast-drying caulks should be avoided due to their shorter life-spans on exterior applications.

How the weather barrier is supposed to work.

“A weather barrier is part of the wall assembly; it prevents the passage of moisture, rain, and wind through critical areas of the walls and roof, and protects vulnerable building components from deterioration.” The weather barrier starts with house wrap in most modern construction applications. This is either stapled or nailed to the exterior walls, and the joints are all sealed with an approved tape. The window and door openings are then wrapped with a weather-resistant tape to help maintain the integrity of the moisture envelope before their installation. These tapes must be properly installed, or the possibility of failure exists.  The top layer of tape must always overlap (not underlap) the layer below it or water can get behind the tape and affect the wall.

Flash above doors and windows.

In days of old, metal flashing was used above doors and windows to maintain the integrity of the moisture envelope on a home.  Today, most windows are manufactured with a built-in, weatherproof nailing flange that replaces the old metal flashing. For this flange to work properly, it must be slid beneath the top layer of window tape so that water cannot get behind the tape and affect the wood structure beneath. If the window is installed against the tape that is attached to the house wrap and then taped over again, the waterproofing is dependent on the tape never losing its grip.  For doors, the standard metal drip strip works fine but also needs to be installed below the window and door wrap tape is applied for a proper seal.

Leave a Reply

Your email address will not be published. Required fields are marked *

Preservative Treated Wood – What Does it Mean?

Wood is an extremely durable material. Properly dried, finished and sealed, wood can last for thousands of years, assuming it’s protected from water, high humidity, and insects. The irony is that when wood isn’t protected from the elements, this durable

Read More »

Why Job Callbacks are so Costly

As a home builder or building materials supplier, your ultimate goal is customer satisfaction. You want to provide materials to your client that provide a high level of reliability, perform as advertised, and are cost-conscious. Remaining profitable is of paramount

Read More »

The Danger of Airborne Silica Dust

Crystalline silica is extremely common in nature. While it’s found in a number of forms, the most common is quartz. Quartz is used in industry as an abrasive, as a chemical component, and as an important element in electronics. It

Read More »
paint brush on wood

Paint Adhesion-Why Is My Topcoat Coming Off?

Poor paint adhesion is an insidious problem. In some cases, the paint will bubble right away, but often the issue doesn’t become evident until some time has passed. The contractor might finish the job, assuming everything is fine, only to

Read More »
Aerial top view of summer green trees in forest in rural Finland.

Which Trim Millwork Products Are The Most Sustainable?

Homebuilders around the country are concerned about sustainability. They want to preserve the planet’s natural beauty, for their children and their children’s children. They recognize the impacts, both positive and negative, that large scale construction projects can have on the

Read More »

Natural Wood Removes Hidden Costs in Trim Loss

You build homes that give your customer quality and value. To do that, you need to be sure that your exterior trim product selection meets this criteria as well. Low maintenance is certainly a necessity for any exterior trim going

Read More »
Rain on umbrella

Moisture-The Root of Many Problems in Exterior Trim

How a company handles the moisture issues connected with the manufacturing process of trim products (window trim, fascia, barge boards, etc.), will determine the overall quality of the finished product when it is delivered to the job site. But equally

Read More »